Supplies Wanted
Two '/*" x Γ eighteen-gauge sterling silver sheet silver Two 7/«" sterling silver bar elements Two 5.three mm x 3.2 mm sixteen-gauge sterling silver oval bounce rings Two sterling silver ear wires
Applications Wanted
Ruler
Marker
Jeweler's noticed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Wonderful grit sanding pad Awl
Challenging, flat surface area /Îί’ drill bit
Handheld rotary Resource, flex shaft, or drill press Liver of sulfur or oxidizing solution Great steel wool Polishing fabric
Two pairs of chain nose pliers
1.Utilize the ruler to evaluate and mark two
rectangle items of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's observed or tin snips, Minimize the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you will end up generating the bracelet and pendant projects, you might want to Reduce the entire rectangle silver items desired for another projects and texture them all at just one time).
3.Area The 2 W x Γ sterling silver rectangle pieces on to the sticky facet of a piece of masking tape. This will let you to hold the silver rectangles in position if you are texturing them, and will even assistance to keep your fingertips at a safe distance to stop hitting them with the hammer.
4.Spot the bit of masking tape While using the silver rectangles sticky side down onto a concrete block or landscape paver.
5.Using a hammer, gently strike the tape-lined silver rectangles utilizing a organization strike, but You should not strike too hard. You'll be able to accomplish the desired texture a lot more very easily with several delicate strikes as opposed to several tough strikes. Raise the tape frequently and check the development with the texturing, ensuring that the whole area with the silver rectangles is getting a uniform texture. The area will glance much like sandpaper if you are employing a concrete block. If you attain the specified texture, get rid of the silver rectangles from the masking tape.
6.the silver rectangles will have a slight curve to them, and the perimeters will probably be misshapen and sharp Once you texture them. You can depart the silver rectangles curved or, to flatten them, put the silver rectangles on a hard, flat men's jewelry floor and utilize a rawhide mallet to flatten them. If you do not Use a rawhide mallet, you can area the silver rectangles on a tough, flat area, include the items which has a thick piece of scrap leather, and make use of a hammer to gently faucet the leather-based included silver rectangles to flatten them.
7.You will have to use a file to reduce any rough or sharp edges. Use a fantastic grit sanding pad to go in excess of the world in which you have filed to clean the perimeters and remove any file marks.
8.Measure from 1 stop of every textured silver rectangle and spot a mark in the center of each piece. This is when the holes are going to be drilled to connect the soar ring and bar parts.
9.Put on the security Eyeglasses. Spot the textured silver rectangles onto gents ring a tough, flat floor. Area the point of the awl over the mark you manufactured '/t" from your finish of the rectangle items and use a hammer to firmly strike once on the highest in the awl to make a pilot gap for drilling the holes into gents ring the silver rectangles.
ten.Using a drill bit, drill holes into each with the silver rectangles having a handheld rotary Resource, flex shaft, or drill press. Remember to wear security Eyeglasses.
11.Make use of men's fashion rings the file or sanding pad to reduce any burs or rough edges still left from drilling holes into the silver rectangles.
12.Implement liver of sulfur or oxidizing Alternative for the textured silver rectangles, bar parts. and bounce rings. It is essential to comply with any protection recommendations the men's gold & silver rings manufacturer indicates when dealing with any substances.
thirteen.After applying the oxidizing Remedy, use high-quality metal wool to eliminate the darkened spots on the raised surface from the silver rectangles, leaving a few of the textured places darkish. Rub the fantastic steel wool more than the jump rings and bar components to eliminate some although not most of the darkened parts. Rinse with drinking water, dry, and rub with sharpening cloth.
fourteen.With two set of chain nose pliers pointing up, hold the jump ring with the opening at the best. Roll just one of the wrists far from both you and your other wrist towards you, opening the jump ring only as much as vital. To close the jump ring, maintain it the identical way and roll your wrists in the opposite course (consider Keeping a piece of paper and tearing it). Hardly ever pull the leap ring finishes out as this will likely weaken the metallic, and it will be tricky to near the bounce ring.
15.Insert the bar component and textured silver rectangle on the bounce ring. Near the soar ring.
sixteen.Gently open up the loop at The underside from the ear wire, insert the other stop with the bar component. then shut the ear wire loop.
seventeen.Repeat these actions for the next earring.